Radio Automobile Drag Racing

Radio Automobile Drag Racing

We bring you the best league in the land. We believe in order for the hobby to continue to grow, innovate and invite more potential drives in we need to reduce the rules needed to race at your local track or street!

Classes

  1. 1/10 Outlaw
  2. 1/7 Outlaw
  3. Top Fuel
  4. Funny Car
  5. Pro Mod
  6. Pro SC (short course)
  7. Pro Stock
  8. Street
  9. 1/8 Basher

Track Rules

  1. Tracks can be prepped or green and is up to the race directors discretion
  2. minimum lane width of 8'
  3. 132' length
  4. Prepping
    1. Track can be sprayed before event
    2. Track can be sprayed in between rounds
  5. Burnouts
    1. A burnout is required
    2. Can burnout on racing surface at the line or behind
    3. Burnouts on wool carpet allowed

Illegal Substances - we are

  1. Prep - no prep or sticky substances allowed
  2. Conditioner - tires can be conditioned but cannot be done at the track
  3. Solvents/degreaser - no solvents or degreasers allowed
  4. Cleaners - such as simple green, WD40, Windex, etc. not allowed.
  5. Any person found with any illegal substance during practice or racing will be disqualified and forfeit their track fee and entry.

Class Rules

  1. 1/10 Outlaw
    1.  Chassis
      1. 13.5" max wheelbase
    2. Battery
      1. Max 2 batteries
      2. No limit to number of cells
      3. Safety - Must be commercially available
    3. Tires
      1. Front
        1. Any tire (3D printed, rubber, rubber band, O-ring or foam)
        2. Max of 4.5" or 124mm diameter.
        3. 12mm or 14mm hex
      2. Rear tire
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Max of 4.5” or 124mm diameter.
        3. 12mm or 14mm hex
    4. Body
      1. Length - minimum must match the wheelbase
      2. Style - any
        1. Body does not have to cover wheels
      3. Safety - Body must cover batteries
  2. 1/7 Outlaw 
    1. Body
      1. Tires
        1. Any tire (3D Printed Rubber, Rubber Band, O-ring, or foam)
      2. Length - minimum must match the wheelbase
  3. Top Fuel
    1. Chassis
      1. Wheelbase
        1. Maximum 30" or 762mm
    2. Motor
      1. Any Commercially produced
    3. ESC 
      1. Any commercially produced
    4.  Battery
      1. Commercially produced
      2. upto 4S Lipo
      3. Max Voltage 16.88V
    5. Tires
      1. Front 
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Can be spindle style, 12mm, or 14mm hex
      2. Rear
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Max of 4.5” or 124mm diameter.
        3. Through Axle,12mm or 14mm hex.
    6. Rear Axle
      1. Must be a solid rear axle
  4. Funny Car
    1. Chassis
      1. Wheelbase
        1. Maximum 21" or 533mm
    2. Motor
      1. Commercially produced
      2. Can Diameter
        1. 36mm Maximum
      3. Can Length
        1. 60mm Maximum
    3. ESC 
      1. Any commercially produced
    4.  Battery
      1. Commercially produced
      2. 4S Lipo
      3. Max Voltage 16.88V
    5. Tires
      1. Front 
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Can be spindle style, 12mm, or 14mm hex
      2. Rear
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Max of 4.5” or 124mm diameter.
        3. Through Axle,12mm or 14mm hex.
    6. Rear Axle
      1. Must be a solid rear axle
    7. Wheelie Bar
      1. Maximum length 10.5"
      2. must use 4 links attached to axle or chassis
  5. Pro Mod
    1. Chassis
      1. Maximum Length 13.5" or 343mm
    2. Motor
      1. Commercially produced
      2. Can Diameter
        1. 36mm Maximum
      3. Can Length
        1. 60mm Maximum
    3. ESC 
      1. Any commercially produced
    4.  Battery
      1. Commercially produced
      2. 2S Lipo
      3. Max Voltage 8.44V
    5. Tires
      1. Front 
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Can be spindle style, 12mm, or 14mm hex
      2. Rear
        1. Any tire (3D Printed, rubber, rubber band, O-ring, or foam
        2. Max of 4.5” or 124mm diameter.
        3. Through Axle,12mm or 14mm hex.
    6. Rear Axle
      1. Must use an axle housing
        1. lockout
        2. differential
  6. Pro SC: Follows www.ProSeriesRCDR.com rules for Outlaw Class
    1. Chassis:
      1. 2WD
      2. 12-13.5" wheelbase
      3. Rear and mid motor configurations are permitted. 
    2. Weight:
      1. 2060g w/body
    3. Body
      1. no extra holes cut in body beside body post holes any 1/10 scale realistic drag car body.( Pro mods allowed)
      2. Body must cover wheels .
      3. Wheel cut out must reveal half the wheel.
      4. spoilers wings Rear spoilers wings and side dams may extend 3” off the rear deck lid and cannot extend past parallel to the roof line
    4. ESC and Motor:
      1. Any commercially available 1/10 RC car motor hardware must be obtainable prior to the event.
      2. Timing and tuning adjustments are allowed.
    5. Battery:
      1. Any 2S (LiPo) Graphene or LiPo HV battery with a 3.1 voltage
      2. limit of 8.44 volts. 
    6. No assists:
      1. Gyros, driving assist items, AVC, and TSM receivers are prohibited. -
    7. Tires:
      1. Any commercially available rear tires/wheels with rubber construction and foam inserts are permitted.
      2. Any commercially available front tires/wheels are permitted including 3D printed tires.
    8. Shocks:
      1. Four shocks must be present on all four corners of the suspension, actively attached to the suspension arm or hub caster block assembly. 
      2. All four shocks must exhibit movement along with suspension arms, with a minimum of 1/4" (6.35 mm or 2.5 inches) of travel. - Prep: Any prep is allowed.
    9. Suspension:
      1. Fully articulated suspension arms, as found on typical short course trucks, must be used with inner hinge pin(s) for attaching steering caster blocks and drive hubs.
      2. Adjustable front or rear suspension arms for toe adjustments are permitted, but no system allowing active toe adjustments is allowed.
  7. Pro Stock: Follows www.ProSeriesRCDR.com rules for Pro Stock Class This class was developed as an introduction to advanced tuning in preparation for Outlaw.
    1. Vehicle modifications are permitted
    2. this includes the replacement of stock components with readily available aftermarket parts (e.g., carbon-fiber components)
    3. Removal of non-essential stock parts, such as the side rails on the Traxxas Drag Slash, Losi 22S, and DR10.
    4. CHASSIS:
    5. Losi
    6. DR10 (NO DR10M or carbon fiber chassis)
    7. Traxxas Drag Slash (Street Eliminator)
    8. Chassis plate must remain as stock and cannot be altered, trimmed, or cut to reduce size and weight.
    9. POWERPLANT & REMOTE:
      1. Factory Motor and ESC, can be mixed.
      2. Stock or Aftermarket remote.
      3. NO GYROS OR TSM ALLOWED!!!
    10. BATTERY:
      1. any 2S battery 
    11. RIMS & TIRES:
      1. Rear
        1. Any commercially available tire/wheels with rubber construction and foam inserts are permitted. 
      2. Front
        1. Any commercially available tire/wheels are permitted including 3D printed tires. 
    12. TIRE PREP:
        1. No Prep with dedicated lane.
    13. WHEELIE BAR:
      1. Any aftermarket wheelie bar no longer than “15in” (Carbon Fiber parts allowed) 
    14. BODY:
      1. Any aftermarket body with or without rear bumper.
      2. Bodies must cover all four wheels
        1. Wheel wells cut to show no less than half the wheel.
        2. Any aftermarket wings allowed No higher than 1 1/2” off the rear deck.
      3. NO FLOATING BODY MOUNTS SUSPENSION:
    15. Suspension
      1. Four shocks must be present on all four corners of the suspension
        1. actively attached to the suspension arm or hub caster block assembly.
        2. All four shocks must exhibit movement along with suspension arms, with a minimum of 1/4" (6.35 mm or 2.5 inches) of travel. (Carbon Fiber parts allowed)
    16. TRANSMISSION:
      1. Stock or Aftermarket casing with internal stock parts (diff).
      2. Stock adjustable slipper clutch or slipper eliminator
  8. Street
    1. Chassis
      1. Upto 13.5" wheelbase
    2. Suspension
      1. must have shocks on all four corners
      2. independent or straight axle allowed
    3. Drivetrain
      1. 4wd and 2wd type transmissions allowed
        1. Buggy, truggy, short course trucks, gt cars, drift cars, pan cars, and tanks allowed. 
        2. Belt drives can be used
      2. Straight axle
        1. Differential and lockers allowed
    4. Tires
      1. Front 
        1. Rubber tires only
        2. Max 4.5" or 124mm
      2. Rear
        1. Rubber tires only
        2. Max 4.5" or 124mm
      3. Slicks are not allowed
        1. Dragworx P90 radial okay
        2. Hand cut radials okay
          1. must have 2 grooves
    5. Motor
      1. Commercially produced
      2. Can Diameter
        1. 36mm Maximum
      3. Can Length
        1. 60mm Maximum
    6. ESC 
      1. Any commercially produced
    7.  Battery
      1. Commercially produced
      2. 2s Lipo
      3. Max voltage 8.44v
    8. Body
      1. Length - minimum must match the wheelbase
      2. Style - any
        1. Body does not have to cover wheels
      3. Safety - Body must cover batteries
  9. Basher
    1. Chassis
      1. any 1/8 or larger
      2. Max wheelbase 25"
    2. Weight
      1. Maximum 30lbs
    3. Battery
      1. Lipo 8S
      2. maximum voltage 33.7V
    4. Wheels
      1. Must be rubber or Foam